PluginLift电梯插件

插件简介

PluginLift 是一款适用于 Paper 1.21.11 的电梯插件。它提供 2×2 轿厢、双格电梯门、楼层显示器、呼梯面板和集选式调度，并使用自定义模型呈现完整的电梯外观。

主要功能

• 固定 2×2 内部空间的电梯轿厢。
• 每层配备两格宽、两格高的电梯门和门顶楼层显示器。
• 呼梯面板通过组件连接器与对应楼层站连接。
• 上行与下行呼梯请求分别排队，电梯优先处理当前运行方向上的请求。
• 轿厢内可打开楼层选择菜单。
• 电梯门检测门口玩家，在关闭过程中遇到阻挡时保持开启或重新打开。
• 使用实体承载层移动乘客，不修改玩家的速度、重力或飞行状态。
• 支持四个朝向的楼层站、呼梯面板和电梯布局。
• 自动保存楼层站、呼梯面板和已组装电梯。

插件物品

建造电梯

1. 管理员执行 /pluginlift give all 获取全部插件物品。
2. 使用楼层站套件在各楼层放置楼层站。所有楼层站必须位于相同的 X/Z 位置、保持相同朝向，并留出畅通的 2×2 竖井空间。
3. 在每层放置呼梯面板。
4. 手持组件连接器，依次右键楼层站和对应的呼梯面板。两者顺序可以互换，连接距离不得超过 16 格。
5. 使用楼层设置器右键楼层站，并在聊天栏输入 楼层编号 | 楼层描述 | 提示音开/关。
6. 每个楼层编号必须唯一。设置完成后，使用竖井同步器右键任意楼层站组装电梯。
7. 点击呼梯面板上半部分登记上行呼梯，点击下半部分登记下行呼梯。
8. 进入轿厢后右键内部区域，打开楼层选择菜单并选择目的楼层。

最高楼层不能登记上行呼梯，最低楼层不能登记下行呼梯。

命令

Overview

PluginLift is an elevator plugin for Paper 1.21.11. It provides a 2×2 cabin, two-block-wide elevator doors, floor displays, hall-call panels, and collective call scheduling, presented with a complete set of custom models.

Main Features

• Elevator cabins with a fixed 2×2 interior.
• Two-block-wide, two-block-high elevator doors and an overhead floor display at every landing.
• Hall-call panels connected to their floor stations with the component connector.
• Separate up and down call queues, with requests in the current travel direction served first.
• An in-cabin floor selection menu.
• Doorway player detection that holds or reopens doors when the entrance is occupied.
• An entity-based carrier floor that moves passengers without changing player velocity, gravity, or flight state.
• Floor stations, hall-call panels, and elevator layouts that support all four horizontal directions.
• Automatic storage of floor stations, hall-call panels, and assembled elevators.

Plugin Items

Building an Elevator

1. Run /pluginlift give all as an administrator to obtain all plugin items.
2. Use the Floor Station Kit to place a station at every floor. All stations must share the same X/Z position and facing, with a clear 2×2 shaft behind the doors.
3. Place a Hall-Call Panel at every floor.
4. Hold the Component Connector and right-click the floor station and its hall-call panel. Either selection order works, and the maximum connection distance is 16 blocks.
5. Right-click each station with the Floor Configurator and enter floor number | floor description | chime on/off in chat. The accepted chime values are 开/关 or on/off.
6. Every floor number must be unique. After configuration, right-click any station with the Shaft Synchronizer to assemble the elevator.
7. Click the upper half of a hall-call panel to register an up call, or the lower half to register a down call.
8. Enter the cabin and right-click its interior to open the floor selection menu and choose a destination.

The top floor cannot register an up call, and the bottom floor cannot register a down call.

Commands